DNP RX1HS Media Guide – 4x6, 5x7 & 6x8 Photo Paper Sizes Compared

Looking for DNP RX1HS media, RX1HS 4×6 paper, RX1HS 5×7 media, or RX1HS 6×8 print kits? This guide covers every media format available for the DNP DS-RX1HS and original DNP RX1 printers — with verified print counts, accurate strip output formats, L-Spacer requirements, software configuration notes, and honest troubleshooting tips from nearly 30 years of supplying these products to working professionals.

DNP DS-RX1HS Overview

This official DNP video covers the DS-RX1HS printer's key features, print speed, and media system — a good starting point if you're researching the platform or introducing it to a new team member.

---

What Is DNP RX1HS Media?

DNP RX1HS media kits are professional dye-sublimation paper and ribbon sets designed exclusively for the DNP DS-RX1HS and the original DNP RX1 photo printers. Each kit includes matched paper rolls and color ribbons engineered to work together as a calibrated system — ensuring consistent color, reliable transport, and durable output across high-volume event and photo booth workflows.

The media lineup covers three standard sizes (4×6, 5×7, 6×8) plus two specialty perforated formats. Glossy or matte finish is selected through the printer driver or photo booth software — both use the same media roll, no separate SKU required.

The RX1HS also supports 2×6 photo booth strip output using standard 4×6 or 6×8 media in 2-up or 4-up software mode. This is handled entirely by software — no perforated media is needed for strip printing. See the Understanding 2×6 Strip Output section below for full details.

Not sure how much media you need for your next event? Use our free Photo Booth Media Calculator to estimate prints and rolls by guest count, event duration, and printer model.

---

All DNP RX1HS Media Kits at a Glance

All kits include 2 paper rolls and 2 matching dye-sublimation ribbons. Media types are not interchangeable between printer models.

---

---

DNP RX1HS 4×6 Media — The Workhorse Kit

DNP RX1HS 5×7 Media — Premium Portrait Format

DNP RX1HS 6×8 Media — Most Versatile Format

---

RX1HS Specialty Perforated Media

The DNP DS-RX1HS supports two factory-perforated media options. These produce different output sizes and serve different use cases — understanding the difference before ordering is important.

4×6 2S Center Perforated — Two 3×4" Prints

6×8 3S Triple Perforated — Three 2×6" Strips

---

Understanding 2×6 Strip Output on the RX1HS

Getting 2×6 photo booth strips from the RX1HS is one of the most common questions we receive. Here is every method available, with the media required and how each one works.

Note: The 4×6 2S Center Perforated media does not produce 2×6 strips. It produces two 3×4" prints. See the perforated section above.

---

Configuring 2-Up Mode in Photo Booth Software

The 2-up strip setting is controlled by your photo booth software or printer driver — not a hardware switch on the printer. Here is how to enable it in the most common platforms used with the RX1HS:

Software versions change. Always confirm current printer support and driver requirements with your software provider before an event. If you experience strip layout issues, check that your DNP driver is the current version from dnpphoto.com/support.

---

How to Load Media Into the DNP RX1HS

This official DNP tutorial covers the complete media loading process for the DS-RX1HS — including paper roll installation, ribbon alignment, and common loading errors to avoid.

Media Loading Best Practices

• Always use the matched paper roll and ribbon from the same kit — never mix components from different boxes
• Open the kit only when you are ready to load — the factory seal protects the ribbon from dust, which is the primary cause of white speckle artifacts in prints
• Handle the paper roll by its edges only — fingerprint oils on the paper surface can cause density variations in finished prints
• For 5×7 media, install the L-Spacers before loading — the paper will not align correctly without them
• After loading, run one test print before the event starts to confirm color, alignment, and finish
• Keep at least one sealed backup roll accessible during the event — not buried in a bag

---

DNP DS-RX1HS Media Options Overview

This official DNP video walks through the full range of media options available for the DS-RX1HS — including standard sizes, perforated formats, and strip output capabilities. A useful reference before placing a media order.

---

Common Mistakes and Troubleshooting

These are the most frequent issues we hear about from RX1HS operators. Most are media-related, not hardware problems.

Banding or Horizontal Lines in Prints

Most likely cause: Dust on the ribbon or print head. This happens when media is opened in a dusty environment or stored unsealed. Always open media in a clean space immediately before loading, and never leave an open roll exposed between events. If banding persists after a fresh roll, the print head may need cleaning — refer to the DNP DS-RX1HS maintenance guide.

Color Shift (Prints Look Too Warm, Too Cool, or Desaturated)

Most likely cause: Mismatched media components — paper from one kit, ribbon from another. Even within the same format, DNP calibrates each paper and ribbon batch as a matched pair. Always use the paper and ribbon that came in the same box. A second common cause is media stored in high heat (above 95°F) — heat exposure degrades the ribbon chemistry before printing.

Paper Jam or Misfeed on 5×7 Media

Most likely cause: Missing or incorrectly installed L-Spacers. The DS-RX1HS spindles are 6 inches wide. Without the L-Spacer set (#90701140S) installed, 5×7 paper (5 inches wide) shifts laterally during transport and triggers a jam. Order replacement L-Spacers here.

Prints Coming Out with the Wrong Finish (Gloss When You Expected Matte)

Most likely cause: The finish setting in the printer driver or photo booth software was not saved between sessions. The DNP RX1HS finish setting (glossy/matte) is set in the Windows printer driver preferences or within your photo booth software's printer settings — it does not change automatically when you reload media. Check your driver settings before every event if you switch between finishes.

Strip Output Not Cutting Correctly in Software

Most likely cause: The printer driver print mode is set to full 4×6 rather than 2-up. Open Windows Printer Preferences for the DNP DS-RX1HS, find the print mode or layout setting, and confirm it is set to 2-up strip mode. Some photo booth software overrides this setting, so also check within the software's own print settings.

Lower Print Yield Than Expected

Most likely cause: Test prints, loading waste, and partial roll tail-end losses. A 700-print roll typically yields 680–695 prints in real-world use after accounting for a test print, any jammed sheets, and the final few sheets where tension can cause inconsistent feeding. Always plan for 2–3% yield loss from a rated roll count, and never start a high-volume event on a roll with fewer prints than your expected total.

---

DNP RX1HS vs. DNP RX1 — What Is Different?

The DNP DS-RX1HS is the updated successor to the original DNP RX1. Both printers use the same media format — all RX1HS media kits work in both models. The primary differences are in print speed and operational features.

---

RX1HS vs. DS620A vs. DS40 — Which Platform Is Right for You?

If you are evaluating DNP printer platforms, here is how the RX1HS compares to the DS620A and DS40. Media types are not interchangeable between these platforms — each requires its own specific media.

---

Print Durability and Media Storage

All DNP RX1HS dye-sublimation prints include a protective overcoat applied automatically during printing. Finished prints are suitable for immediate handling in professional photo booth, event, and retail environments.

• Smudge-resistant: Safe to handle immediately after printing
• Water-resistant: The overcoat protects against everyday moisture exposure
• Fade-resistant: Rated for long-lasting indoor display under normal conditions
• Scratch-resistant: The laminate layer protects surface quality during handling

Media Storage Guidelines

Store unopened rolls in a cool, dry location away from direct sunlight. Avoid vehicle trunks, heat vents, and humid environments.

• Recommended temperature: 59°F–77°F (15°C–25°C)
• Recommended humidity: 40%–60% relative humidity
• Unopened shelf life: Approximately 2 years from manufacture date
• Never mix paper and ribbon from different kits — even of the same format

For detailed event planning guidance — including how many rolls to bring based on guest count, event duration, and printer model — see our Photo Booth Media Calculator and Planning Guide.

---

Why Buy From EventPrinters.com

EventPrinters.com is operated by Southtrend Corp, an Authorized DNP Dealer serving the professional photo industry since 1996. We have supplied DNP RX1HS and RX1 media to photo booth operators, event photographers, retail photo labs, and mobile print businesses across the USA and Latin America since the printer launched.

• Guaranteed authentic, factory-sealed DNP media — not gray-market stock
• Technical support from a team that has sold and used these products since 1996
• Volume pricing and dealer rates available for qualified buyers
• Free ground shipping on orders over $149 within the contiguous United States
• Ships from Miami, Florida

Questions, volume pricing, or troubleshooting? Call (305) 653-0037, Monday–Friday, 9am–5pm EST, or visit our contact page.

---

Frequently Asked Questions

What media sizes does the DNP RX1HS use?

The DNP DS-RX1HS supports 4×6, 5×7, and 6×8 standard media kits, plus two specialty perforated options: the 4×6 2S center-perforated media (two 3×4" prints per sheet) and the 6×8 3S triple-strip media (three 2×6" strips per sheet).

How many prints are in a DNP RX1HS media kit?

The 4×6 kit yields 1,400 prints (2 rolls × 700), the 5×7 kit yields 800 prints (2 rolls × 400), and the 6×8 kit yields 700 prints (2 rolls × 350). All kits include 2 matched paper rolls and 2 ribbons. For event planning estimates, use our free media calculator.

How do I get 2×6 photo strips from the DNP RX1HS?

Use the standard 4×6 media with your printer driver or photo booth software set to 2-up mode. The software cuts each 4×6 sheet lengthwise into two 2×6 strips, yielding up to 2,800 strips per kit. You can also use the standard 6×8 media in 4-up mode for four 2×6 strips per sheet, or the 6×8 3S perforated media for physical tear-off strips. No perforated media is needed for standard 2×6 strip output.

What does the 4×6 2S center perforated media produce?

The 4×6 2S media has a center perforation that cuts the sheet horizontally, producing two 3×4" prints per sheet — not 2×6 strips. It is designed for dual-image keepsakes, vouchers, coupons, and branded tear-off applications. For 2×6 strips, use standard 4×6 media in 2-up software mode.

Does the RX1HS need different media for glossy vs. matte output?

No. Both glossy and matte output are produced from the same media roll. The finish is selected through the printer driver or photo booth software. No separate media SKU is required for each finish.

Is DNP RX1 media the same as RX1HS media?

Yes. The DNP RX1 and DS-RX1HS are compatible with the same media kits. All media listed on this page works with both printer models. Note: 5×7 printing on the original RX1 requires firmware v2.04 or later.

Does the RX1HS require special accessories for 5×7 printing?

Yes. The DNP L-Spacer set (part #90701140S) must be installed on the paper spindles before loading 5×7 media. New DS-RX1HS printers include these spacers. Order replacement spacers here if yours are missing.

What is the print speed of the DNP DS-RX1HS?

The DNP DS-RX1HS produces a finished 4×6 print in approximately 12.4 seconds, with throughput up to approximately 290 prints per hour in high-speed mode. The original DNP RX1 prints a 4×6 in approximately 15 seconds.

How do I configure 2-up strip mode in my photo booth software?

The method varies by software. In dslrBooth, set the print layout to "2×6 Strip" in Settings → Print. In Darkroom Booth, choose a 2×6 template in the Layout Editor. In Breeze Systems, set 2-up mode in Printer Settings. For all platforms, also confirm the DNP driver's print mode is set to 2-up in Windows Printer Preferences. See the full software configuration table in this guide for platform-specific steps.

Why are my RX1HS prints showing banding or color shift?

Banding is usually caused by dust on the ribbon from opening media in a dusty environment. Color shift is almost always caused by mixing paper and ribbon from different media kits. Always use matched components from the same box, open media only when loading, and store unused rolls in sealed packaging. If issues persist after a fresh kit, the print head may need cleaning.

Where can I buy genuine DNP RX1HS media?

Purchase directly from EventPrinters.com. Free ground shipping on orders over $149 within the contiguous USA. For volume pricing or technical support, call (305) 653-0037 or visit our contact page.